Maple Walnut Fudge - Grandma's Perfected Melt-in-your-Mouth Recipe (2024)

FAQs

What is the secret to good fudge? ›

After letting the fudge cool, it's time to beat it. It is important to stir constantly with a wooden spoon until the mixture starts to thicken and its surface starts to look dull or matte. Now is the time to stop beating and pour the fudge into a mould.

By cooling the fudge prior to agitation (like in the recipes included in this article), on the other hand, you'll get much smaller, finer sugar crystals and a finished fudge with a smooth, creamy texture. Cool the mixture until it reads 120° F on the thermometer—no stirring. This can take 1 to 1/2 hours.

If your fudge turned out super sticky, or it didn't set as it cooled, it probably never got hot enough. This mistake is super easy to avoid if you use a candy thermometer and cook the fudge to the temperature specified in the recipe (usually between 234 and 239°F).

Evaporated milk doesn't have sugar added. The sweetened condended milk is needed as no extra sugar is added to the fudge. If evaporated milk were used then the fudge would not be sweet enough and also would still be too soft unless the fudge is frozen.

You have to control two temperatures to make successful fudge: the cooking temperature AND the temperature at which the mixture cools before stirring to make it crystallize. Confectionery experiments have shown that the ideal cooking temperature for fudge is around 114 to 115 °C (237 to 239 °F).

Allow the fudge mixture to rest until the temperature registers between 150°-160°. Once the desired temperature is reached, beat the ever-loving stuffing out of the fudge. Two to three minutes of hardcore mixing (by hand). This is where you earn the right to eat half of the batch.

If you forget to beat the fudge, try heating it back up over low heat, then beat it once it's slightly softened. If you beat the fudge too soon, the crystals will be too large, and the fudge will be grainy.

Once a seed crystal forms, it grows bigger and bigger as the fudge cools. A lot of big crystals in fudge makes it grainy. By letting the fudge cool without stirring, you avoid creating seed crystals. Stirring would help sucrose molecules "find" one another and start forming crystals.

What to do with ruined fudge? ›

Good use of failed fudge: fudge that is too hard, too soft, too runny, too sugary, too chewy, etc. Proportions are as follows: for every 2 cups (roughly 1 pound yield) of any failed fudge that is not runny, you'll need 1 egg, ½ cup all-purpose flour, and ½ cup milk. If fudge is soupy, halve the milk (to ¼ cup).

The ingredients for fudge are combined and cooked to 234 degrees, cooled to 110 degrees without stirring, then beaten until creamy. Candy that isn't cooked long enough will end up too soft; overcooking makes fudge crumbly or hard.

The main reason is that your Fudge has not reached the optimum temperature. If your mixture only reaches 110 or 112 degrees Celsius it will always be soft. That's why we recommend investing in a sugar thermometer. Another reason your Fudge is not setting is that the ratio of liquid to sugar is too high.

It could be that your fudge is overcooked and this causes the sugar to harden. A sugar thermometer will help you to check it reaches the correct temperature which is the soft ball stage at 112 to 116 °C (234 to 241 °F). If it exceeds this, it is heading for a much chewier consistency.

NEVER REFRIGERATE your fudge as this will draw out the moisture and leave you with dry, crumbly fudge.

While you ultimately want crystals to form, it's important that they don't form too early. The key to successful, nongrainy fudge is in the cooling, not the cooking.

Cream of tartar is used in caramel sauces and fudge to help prevent the sugar from crystallizing while cooking. It also prevents cooling sugars from forming brittle crystals, this is why it's the secret ingredient in snickerdoodles!

Prevent Graininess Before It Starts

The most common reason for graininess is because you began beating or stirring it while the fudge was still cooling. It's best to wait until it's cooled to somewhere around 110 to 113 degrees to begin stirring.